1) Compatibility

    Ultimate 2 Bluetooth: Switch 1/2, Windows, Steam Deck.

    Ultimate 2 Wireless 2.4G: Switch 1/2(Latest firmware), Windows, Android, Steam Deck.

2) Colors:

    Ultimate 2 Bluetooth: Yellow (AKNES), Black, White.

    Ultimate 2 Wireless 2.4G: Green(AKNES), Black, White, Purple, WUCHANG: Fallen Feathers(Official Collaboration).

3) Price:

    Ultimate 2 Bluetooth: $69.99.

    Ultimate 2 Wireless 2.4G: $59.99.

4) ABXY buttons layout.

1) Press and hold the Home button for 3 seconds to turn off.

2) Press and hold the Home button for 8 seconds to force turn off.

3) If the device is not connected after powering on, it will automatically turn off after 1 minute.

4) It will automatically turn off after 15 minutes of no operation.

5) It cannot be turn off when connected by a wire, and it will not turn off automatically as well.

1) Battery capacity: 1000mAh.

2) Charging time: About 3 hours.

3) Battery life: About 12 hours.

1) Single or multiple buttons on the controller can be mapped to the L4/R4/PL/PR buttons.

    Note 1: LS/RS are not supported.

    Note 2: The Mapping LED will blink continuously when the configured button is pressed.

Turbo works on most action buttons except:
1) D-pad.

2) Home button.

3) LS/RS.

4) L4/R4 and PL/PR.

No. Settings will automatically reset to default when:

1) Power off.

2) Disconnect.

3) Sleep mode.

The Mapping LED will blink continuously when the configured button is pressed.

⚠️ Limitations:

• D-pad, Home, LS/RS, L4/R4, and PL/PR buttons are not supported for turbo.

• Settings will revert to default settings after the controller is powered-off/disconnected.

• The Mapping LED will blink continuously when the configured button is pressed.

🎮 Configuration:

① Enable Turbo (e.g. Y button):
     Hold Y → Press ★ once → Release → Slow blink

② Disable Turbo:
     Repeat step ① → LED off

③ Enable Auto Turbo (e.g. Y button):
     Hold Y → Double-press ★ → Release → Rapid blink

④ Disable Auto Turbo:
     Hold Y → Press ★ once → Release → LED off

Please follow the steps below:

1) Controller in the powered-on state, press and hold the L1+R1+Minus+Plus buttons for 8 seconds to enter the calibration mode, the Status LED will start to blink.

2) Push the joysticks to the edge and rotate them slowly 2–3 times. Slowly press the triggers to the bottom 2–3 times.

3) Press the same L1+R1+Minus+Plus buttons combination again to complete the calibration.

• Please visit app.8bitdo.cn/Ultimate-Software-V2 download the software to make adjustments.

• Yes, you can customize the RGB lighting effects using Ultimate Software V2.
• Visit app.8bitdo.cn/Ultimate-Software-V2 download the software to make adjustments.

Press the ★ button to cycle through:

① Light-tracing → ② Fire Ring → ③ Rainbow Ring → ④ Off

1) Applicable modes:

    i, Light-tracing mode.

    ii, Rainbow Ring mode.

2) Adjust:

    Press and hold ★ + ▲/▼ on D-pad.

1) Applicable modes:

    i, Light-tracing.

    ii, Rainbow Ring.

2) Method:

    Hold ★ + ◀/▶ on D-pad.

1) Exclusive to Fire Ring mode:
    Hold ★ + ▲/▼ on D-pad

• No, each adapter can only support one controller connection at a time.

• HallPi TMR joysticks.

1) Please ensure the controller is already paired with the Switch console. (Unpaired controllers cannot wake up the Switch console.)

2) Press the Home button to turn on the controller.

3) Shake the controller to wake up the Switch console from sleep mode and automatic reconnection.